Carbon Monoxide Detector Manual (SSCO1) Introduction The SSCO1 wireless carbon monoxide (CO) detector monitors the level of CO gas in your home and gives early warning when a potentially dangerous level exists. It does not detect fire, smoke, or any other gas. If a dangerous concentration of CO is detected, the red light on the front of the detector turns on and an internal siren sounds (4 ...
· Correspondingly, what does the red light on my carbon monoxide detector mean? Red Lights on a Carbon Monoxide Detector Mean Business While that's a bit counter-intuitive, it's the way these systems work. For detectors that normally have flashing green lights, a flashing red light can mean that the batteries need to be replaced or there's another type of malfunction that needs to be …
A beeping carbon monoxide detector may also be a sign that it’s doing exactly what it was designed to do. When CO levels become dangerously high, your CO detector will signal its alarm. Don’t always assume that the CO leak is inside your building-it may be from a neighbouring house. If you’ve realised that you are inadvertently breathing in carbon monoxide, do the safe thing and move ...
The flashing on your plug-in carbon monoxide alarm should stop after 5 minutes, then the light will stay a steady green. Can you reset a plug-in carbon monoxide alarm with the test/silence button? No, the test/silence button only tests or silences the carbon monoxide alarm. To reset the alarm, the unit needs fresh air and time to burn the contamination off the sensor. Push and hold the silence ...
· Carbon Monoxide Detector Beeping Every 30 or 60 Seconds; The last thing we want to hear in the middle of the night is our carbon monoxide detector making a consistent chirping sound. It’s annoying, but it’s usually nothing to worry about. This sort of noise usually means one of the following: the battery is low and needs to be replaced or the alarm has malfunctioned. The best way to deal ...
Carbon Monoxide detector. When activated, the Carbon Monoxide alarm sends a signal to the Pager or SignWave to alert the user. The alarm will also sound a horn and the red indicator will flash at different speeds to indicate the presence of different levels of CO gas, (Slow flashes indicate low levels & rapid flashes indicate high levels).
Yellow flash every 12 seconds: One 100ms chirp every 45 seconds (press button to hush for 12 hours) Detector end of life: Yellow flash every 23 seconds: One 100ms chirp every 45 seconds: Powering up: Green, yellow and red flash sequence every 12 seconds: One 100ms chirp at end of power-up sequence: Tamper: Green, yellow and red flash sequence ...
Provides Carbon Monoxide Gas Detection in residential, multi-family, and commercial office environments - UL Listed, CSFM Approved Product Downloads Diagrams Approvals / Certifications View all of our product downloads here. Key Features 9-32 VDC input Flush or Surface Mount Enclosure or Alarm Relay Trouble/Supervisory relay 10 Year electrochemical sensor Coverage Area: …
· This carbon monoxide detector is designed to detect CO gas from ANY source of combustion.! WARNING Use only for monitoring the gas which the sensor and detector are designed to monitor. Failure to do so may result in exposures to gases not detectable and cause sickness or death. For proper use, see supervisor or User Instructions, or call Macurco Technical Service. Do Not Use …
· 8 signs YOU'VE got a carbon monoxide leak. 1. LOOK for stains, soot or discolouration on or around your boiler, fire or water heater. Flames of a lazy yellow or orange colour on your gas hob ...
On First Alert carbon monoxide detectors, check to see if the battery light is yellow or green. If the alarm is chirping and the light is yellow, it means the battery is low. The way to get a carbon monoxide alarm to stop chirping is to replace the battery.
There are several things that the flashing lights could indicate: Power visual indicator flashing means the detector's power supply voltage is too high or too low. Carbon Monoxide indicator flashing means the CO alarm is disabled because the alarm is resetting or stabilizing OR the unit has gone into fault mode (which could mean a sensor is bad).
· Yellow and orange have traditionally become colors of caution. Like yellow lights and orange road cones, other types of devices that involve these colors help indicate that there’s something to be considered. A flashing orange light on a carbon monoxide detector generally means there is a problem with the detector itself.
This Kidde Smoke/CO Alarm was designed to detect both smoke and carbon monoxide from any source of combustion in a residential environ-ment. It is not designed for use in a recreational vehicle (RV) or boat. P/N: 2534-7201 RevA For your convenience, write down the following information. If you call Product Support, these are the first questions you will be asked. Smoke Alarm Model Number ...
Professional gas sensing solution supplier with over 30-year gas sensor manufacturing experience
Contact Us